[ Pobierz całość w formacie PDF ]
BFO Metal Detector (Beat Frequency Oscillator)
Strona 1 z 3
BFO Metal Detector
(Beat Frequency Oscillator):
Description:
This metal detector is of the older variety, however, very sensitive. It is not extremely temperature stable and
as such will require that you allow it to adjust to the relative temperature in which you are using it. Beyond
that, it is extremely sensitive and capable of detecting very small objects at a depth of at least 8 inches. The
oscillators in this circuit operate just below the bottom end of the AM Broadcast Band at a frequency of 494
KHZ. Although this is a bit high for a BFO metal detector, it allows for the finding of very small objects such as
small rings and coins.
How it Works:
One JFET oscillator working with the search coil operates
around 494 KHZ. The other oscillator operates at about 494.1
KHZ. Although you cannot hear either of these……the difference
is about 100 HZ which is produced in the mixer stage. As metal
is brought near the search coil…the frequency shifts a bit,
producing an audible frequency shift that can be heard in the
earphones. A following stage, amplifies the audio signal and
drives the 8 ohm earphone.
2012-04-24
BFO Metal Detector (Beat Frequency Oscillator)
Strona 2 z 3
To operate the detector: Adjust the frequency of the local oscillator by adjusting the slug in L2, then adjust
variable capacitor so that a low audio frequency of around 40 to 300 HZ is heard. When this tone shifts….the
detector coil has just passed over a metallic object. This circuit employs buffer stages to isolate the outputs of
each oscillator from each other, thus eliminating oscillator pulling which greatly increases sensitivity. It takes
practice to use this unit, however the results can be quite rewarding. The lower that you can set the frequency
with the variable capacitor ….the more sensitive it is to detecting underground objects.
Construction:
PC Board: 3 ¼ long by 1 7/8 inches wide. The aluminum case is 4 ½ long by 3 ½ wide by 2 ¼ high.
Search Coil: This is composed of 22 turns of #28 enameled wire wound on a 6 ¼ inch diameter form and then
wrapped in tape…followed by a wrapping of aluminum foil as a shield. The aluminum foil should only go around
about 355 degrees and should not again touch itself. This would produce an rf short. Now wrap about 8 inches
of tinned #20 wire around one end of the aluminum foil and connect this to one end of the coil. This
connection will go to point “A”on the pc board, the other end of the coil goes to point “B”.
2012-04-24
BFO Metal Detector (Beat Frequency Oscillator)
Strona 3 z 3
The PVC pipe for the search head was cut to 31 inches in length which allowed for 2 inches to go into the
aluminum case. The angle to the search head is 71 degrees.
The local oscillator coil, L2, consists of 291 turns of #32 enameled wire wound on a ¼ inch diameter ceramic,
adjustable ferrite slug, coil form and then coated with epoxy adhesive. This connects to points C and D on the
PC board.
Parts List for the 494 KHZ Metal Detector:
(resistors are 1⁄4 watt)
R1,2,7,8,12
4.7 K
C1
10 pF *(Mica)
R3,4,5,6,9
12 K
C2,3,6,7
330 pF *(Mica)
R10
47 K
C4,8
.001 uF *(Mica)
R11
470 K
C5
12-24 pF Variable
R13,17
5.1K
C9,10
100 pF
R14
560 Ohms
C11,12,14,17
.047 uF
R15
10 K Pot.
C13
47 uF / 35V
R16
22K
C15
100 uF / 35V
R18
47 Ohms
C16,18
22 uF / 35V
* Or any other high quality, stable capacitor device.
L1 (The search coil) 22 turns of #28 enameled wire on a 6 ¼ inch diameter.
This coil also has an aluminum Faraday shield. (see text)
L2 (The local osc. coil) 291 turns of #32 enameled wire on a 1⁄4 inch diameter
Ceramic form with an adjustable ferrite core. Coil windings are over a
½ inch length and then covered with epoxy resin.
Q1,2,5
2N5951 JFET Transistors
Q3,4,6,7
2N2222 BJT Transistors
D1
1N34 or 1N270 Germanium Diode
D2
6.8 Volt Zener Diode (1W)
Home
|
High Selectivity Crystal Radio with Short Wave
|
High Sensitivity BFO Metal Detector
Battery Life Chart
|
Parabolic Microphone
|
Very High Gain Audio Amplifier
|
Audio Sine Wave Generator
One Tube DX Receiver
|
Telephone Line Use Monitor
|
Moisture Detector
|
Vacuum Tube Amplifier
2012-04-24
[ Pobierz całość w formacie PDF ]
© 2009 Po zniszczeniu przeszłości przyszedł czas na budowanie przyszłości. - Ceske - Sjezdovky .cz. Design downloaded from free website templates